One dense 10-metre reel of 5050 RGB LEDs on a 24V supply: enough to ring a bedroom ceiling or line a kitchen, washing the room in one colour that swells with the music.
The ALED LIGHT kit is the classic 5050 RGB strip done long and dense: one 10-metre reel, 600 LEDs, 60 in every metre. That density matters when the strip shines onto a surface you look at, like a ceiling cove or the wall above a headboard. Gaps between beads shrink, so the glow reads as one soft band rather than a string of bright points.
Inside every 5mm-square 5050 package sit three tiny emitters, one each for red, green and blue. Mixing them gives the 16 million shades in the duoCo Strip app, plus a mixed white for plain light when the party is over. Because it is RGB rather than RGBIC, all 600 beads share a single shade and fade, jump or strobe in unison.
The 24V design is the quiet hero here. Higher voltage means less current down a long run, so the far end of the reel stays closer in brightness to the start than a 12V strip of the same length. ALED also builds in two layers of circuitry and copper brackets, both there to carry that current without hot spots.
The LEDs are rated past 50,000 hours and the kit carries a 36-month warranty, long for a strip in this family. The working range runs from -20°C to 60°C, but the strip itself is bare and non-waterproof, so it lives indoors and away from splashes.
| Spec | Value |
|---|---|
| LED type | 5050 SMD RGB |
| Length | 10m (32.8ft) |
| LED count | 600 |
| Density | 60 LEDs per metre |
| Voltage | 24V DC |
| Power supply | 24V mains adapter, included |
| Rated power | 120W |
| Beam angle | 120° |
| Cut points | Every 3 LEDs |
| Colours | 16 million in the app, plus mixed white |
| App | duoCo Strip (Bluetooth) |
| Remote | 44-key infrared, about 10m with clear line of sight |
| Sound reaction | Built-in microphone, music mode |
| Timer and memory | Yes, restores the last mode after power-off |
| Water resistance | None, indoor use |
| Working temperature | -20°C to 60°C |
| LED lifespan | Over 50,000 hours |
| Warranty | 36 months |
| In the box | Strip reel, control box, 44-key remote, power supply |
| Model | AL103001 |
Put the controller into music mode and the ceiling becomes a light show for the kitchen party. A built-in microphone in the control box hears the room, so a speaker on the counter, a guitar or a chorus of guests all move the colour. The reel flashes and fades with the rhythm, one shade sweeping across all 600 beads.
Three things share the controls:
For dinner, a static amber at a quarter brightness turns a ceiling cove into candlelight. For dancing, pick a jump or strobe mode and let the mic set the pace; lower the sensitivity if chatter sets it twitching. The timer handles the everyday part, fading the glow up at dusk and off after midnight without a tap.
Infrared needs line of sight, which is the one catch with a strip hidden above cabinets. Leave the control box's sensor peeking out from the cabinet lip, or lean on the app, which reaches through walls within Bluetooth range.
Plan the run before peeling a single inch of tape. Ten metres suits a bedroom ceiling perimeter, the tops of a long row of kitchen cabinets or a stair wall. Measure the path, mark the corners and decide where the adapter plugs in, since that end starts the run.
A piece cut off beyond the controller is spare strip. It lights only if it returns to the circuit through a 4-pin connector or solder, and connectors are not in the box. Plan the layout so the reel goes on in one piece wherever you can.
Where the light lands sets the mood. Facing the strip up into a cove bounces a soft wash off the ceiling; facing it down from under a cabinet throws brighter light onto the worktop; behind a headboard it paints the wall. Aluminium channel with a diffuser, bought separately, hides the beads completely and helps the tape hold on warm or textured surfaces.
Painted plaster and raw wood can let the tape creep over time. A few mounting clips, or a thin strip of extra double-sided tape along the worst corners, keeps the reel tight to the ceiling through summer heat.
The ALED kit plays the steady role in the family: a dense RGB reel on a long-life 24V supply with a warranty to match. It fits a household that wants a room washed in one colour at a time, with music sync for parties and white for cooking. Where it steps aside is motion, because a plain RGB strip cannot run a rainbow along its length.
| Strip | Colour style | Best moment |
|---|---|---|
| ALED LIGHT 5050, 33ft | One colour across 600 LEDs | Ceiling coves, kitchen parties, plain white |
| HOUHUI RGBIC, 32.8ft | Several colours chasing at once | Game rooms and bedrooms that want movement |
| UETGRE COB RGB+IC, 65.6ft | Dot-free COB line with chasing | Open shelves and desks where beads would show |
Check these before ordering:
Anyone with an older strip whose remote has vanished may not need a new reel at all. A Sunity Bluetooth controller adds app control and a music mode to a 4-pin RGB strip; match its voltage range to the strip first.
As a gift, the ALED reel suits someone moving into a first flat with a bare ceiling and a love of parties. It arrives with everything needed to glow on the first evening, and the three-year cover means a dead section is the maker's problem, not theirs. The app rundown sorts duoCo Strip from Lotus Lantern and the rest of the family.
No. It is a bare, non-waterproof strip for dry indoor surfaces such as ceilings, cabinets and headboards.
No. Being plain RGB, all 600 LEDs change together. Rainbows that travel need an RGBIC strip.
On the marked copper pads, every 3 LEDs. Pieces cut off stay dark unless reconnected with a 4-pin connector or solder.
duoCo Strip, over Bluetooth. The controller may show up as ELK-BLEDOM in a Bluetooth scan; connect inside the app instead.
About 10m. Being infrared, it must be aimed at the control box with nothing in the way.